GOLFJOY Rigel 3 Pro User Manual

I

Product Components

Launch Monitor Main Unit1 piece, including bracket

Power Adapter1 piece

Clubhead Stickers5 sheets

Calibration Plate1 piece

Conversion Connector1 piece

Screw Washer1 pack

Component specifications

No.	Name	Quantity	Unit	Specification
1	Launch Monitor Main Unit (including bracket)	1	Piece	\
2	Power Adapter	1	Piece	Input: 100-240VAC, 50/60Hz, 1.3A; Output: 24V-3.75A, 90W MAX
3	Clubhead Stickers	5	Sheets	Each sticker diameter: outer 5mm, inner 2.5mm
4	Calibration Plate	1	Piece	\
5	Conversion Connector	1	Piece	3-hole to DC connector
6	Screw Washer	1	Pack	\

II / 1

Launch Monitor Introduction

Sensor Type

Overhead-mounted, triple high-speed camera launch monitor

Product Name

GOLFJOY Rigel 3 Pro

II / 2

Launch Monitor Basic Parameters

InstallationOverheadFront-mounted

Install Height2.75–3.1 m2.91–3.1 m with 3D Stance Hitting Mat

TEE Distance110 cm

CalibrationAutomaticNo camera/focus/infrared light adjustment

Supported BallsAny ballIncluding pure white balls

Hitting Zone60 × 60 mm

Ball Data7 metrics

Club Data11 metrics

Full basic parameters

Installation Method	Overhead, front-mounted
Installation Height	2.75–3.1 meters (without 3D Stance Hitting Mat); 2.91–3.1 meters (with 3D Stance Hitting Mat)
TEE Distance	110 cm
Calibration Method	No need for camera/focus/infrared light adjustments, automatic calibration
Supported Balls	Any ball (including pure white balls)
Rough and Bunker	Supported
3D Stance Hitting Mat	Supported
Weight	4.95 kg; 5.95 kg (with wall bracket)
Dimensions	75.6 cm (Length) × 16 cm (Width) × 7/12.7 cm (Thickness)
Number of Lenses	3
Illumination	40 LEDs × 2 sets
Hitting Zone	60 mm × 60mm
Ball Data	7 metrics: Ball speed, launch angle, launch direction, backspin, side spin, spin axis, spin rate.
Club Data	11 metrics: Club speed, attack angle, club path, face angle, face to path, impact location, dynamic loft, spin loft, closure rate, low point, smash factor
Trajector Data	24 metrics
Power	Input: 100-240VAC/50-60 Hz 2.5A; Output: 24V, 3.75A, 90W
Material	Aluminum alloy + TPU
Color	Gray with black
Connection Method	Ethernet
Applicable Environment	Indoor
Operating Temperature	-10°C to 40°C (Power-on test at -10°C)
Altitude	Below 3000 meters
Humidity	20% to 70%
Storage Temperature	-20°C to 80°C

II / 3

External Interfaces / Buttons

REPLACE IMAGE: External interfaces and buttons diagram

Power Button
Press to power on. Press again to power off.

Power Port
Connects to a 24V power adapter.

Ethernet Port
Connects to a Gigabit Ethernet cable for calibration and golf ball operations.

II / 3

Status Indicator Lights

During Power-Up: Blue light flashes.

Power-Up Complete: Blue light stays on.

Connected to Client/App: Blue light stays on.

Ball Detected: Green light stays on.

No Club Data Zone, Ball Detected: White light stays on.

Fault Alarm: Red light flashes.

II / 4

Function Description

One-click calibration

No lens, focus, infrared light board adjustments, or configurations.

Triple high-speed cameras

Wide field of view with 60×60 cm sensor detection area.

3D Stance / Rough / Bunker

Compatible with 3D Stance Hitting Mat, rough and bunker grass.

Any ball

Supports any ball, including pure white balls.

Clubhead replay

Supports clubhead trajectory replay and frame-by-frame impact analysis.

Left / Right handed users

Supports both left and right-handed users.

Sleep mode

Default 15 minutes. Move or cover the ball to wake the launch monitor.

WiFi

Works with GOLFJOY PRO and GOLFJOY SPACE apps.

Certification

Certified by CE, FCC, RoHS, and other international certifications.

III / 1

External Calibration · Installation Positioning

REPLACE IMAGE: Installation tools — Prepare the tools shown below.

REPLACE IMAGE: Installation positioning diagram — Install the launch monitor as shown in the diagram.

MountingClip-onMount the base, slide into the clip, secure with safety screws.

DirectionFront-mounted

Install Height2.75–3.1 m

TEE Distance110 cm

Note: For 3D Stance Hitting Mat compatibility, the installation height is 2.91 to 3.1 meters.

III / 2

Calibration

1

Automatic Network Setup

Open GolfjoyInstallHelper.exe. Select Rigel 3 Pro and click Next.

2

Place Calibration Plate

Place the plate in the green box. Cover the TEE and point the arrow toward the hitting direction.

3

Mark the Area

Mark only the left area. Skip rough or bunker if they are not configured.

III / 3

Clubhead Sticker Method

PurposeClubhead dataRequired for high-precision clubhead data.

MethodFive-pointUse the provided circular stickers.

Detection AreaYellow areaHit balls within the designated yellow detection area.

PlacementSmall error acceptedA small margin of error is acceptable.

For Wood Clubs

Align the 2nd, 4th, and sweet spot horizontally.

Place the 2nd point 5mm from the left edge and the 4th point 5mm from the right edge.

Keep the line from 2nd to 1st parallel to the centerline.

Place the 5th point on the centerline, 5mm from the top.

Place the 3rd point on the bottom score line, close to the left edge.

For Iron Clubs

Align the 2nd, 4th, and sweet spot horizontally.

Place the 2nd point at the left edge and the 4th point at the right edge.

Place the 1st point on the left edge of the second score line from the top.

Place the 3rd point on the left edge of the second score line from the bottom.

Place the 5th point on the centerline, 5mm from the top.

III / 4

Ball Test

Test result

Once the software detects the ball, hit and check whether the data and playback video are available.

REPLACE IMAGE: Ball test interface — Ball test interface

III / 5

Area Verification

1

TEE Area Verification

Place the ball on the TEE. The client will prompt verification.

2

Rough Area Verification

Place the ball on the rough area. The client will prompt verification.

3

Bunker Area Verification

Place the ball on the bunker area. The client will prompt verification.